manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Hardware Reference Manual

The Analog Devices EZ-KIT Lite ADSP-BF506F is a high-performance digital signal processing platform. Access the comprehensive System Manual for free download on manualshive.com, offering detailed instructions, enabling users to maximize the potential of their ADSP-BF506F kit. Explore the unbeatable capabilities of this product with our user-friendly manual.

Share
Download
background image

Reset and Power-up

24-6

ADSP-BF50x Blackfin Processor Hardware Reference

In order to perform a system reset, the

bfrom_SysControl()

rou-

tine must be called while executing from L1 memory (either as
cache or as SRAM). When L1 instruction memory is configured as
cache, make sure the system reset sequence is read into the cache.

After either the watchdog or system software reset is initiated, the proces-
sor ensures that all asynchronous peripherals have recognized and
completed a reset.

For a reset generated by formatting the watchdog timer, the processor
transitions into the boot mode sequence. The boot mode is configured by
the state of the

BMODE

bit field in the

SYSCR

register.

A software reset is initiated by executing the

RAISE 1

instruction or setting

the software reset (

SYSRST

) bit in the core debug control register (

DBGCTL

)

(

DBGCTL

is not visible to the memory map) through emulation software

through the JTAG port.

A software reset only affects the state of the core. The boot kernel immedi-
ately issues a system reset to keep consistency with the system domain.

On a hardware reset, the boot kernel initializes the

EVT1

register to

0xFFA0 0000. When the booting process completes, the boot kernel
jumps to the location provided by the

EVT1

vector register. The content of

the

EVT1

register is overwritten by the

TARGET ADDRESS

field of the first

block of the applied boot stream. If the

BCODE

field of the

SYSCR

register is

set to 1 (no boot option), the

EVT1

register is not modified by the boot

kernel on software resets. Therefore, programs can control the reset vector
for software resets through the

EVT1

register. This process is illustrated by

the flow chart in

Figure 24-1

.

The content of the

EVT1

register may be undefined in emulator sessions.

Summary of Contents for EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EZ-KIT Lite ADSP-BF506F

Zapi SMART CONSOLE User Manual preview
SMART CONSOLE
Brand: Zapi Pages: 50
Linear Analog Devices DC2605A Demo Manual preview
Analog Devices DC2605A
Brand: Linear Pages: 16
Texas Instruments INA293EVM User Manual preview
INA293EVM
Brand: Texas Instruments Pages: 19
Modular AN003 MPT11210IL User Manual preview
AN003 MPT11210IL
Brand: Modular Pages: 9
XFX GeForce 8300 (MI-A78U-8309) User Manual preview
GeForce 8300 (MI-A78U-8309)
Brand: XFX Pages: 26
MSI MS-6764 User Manual preview
MS-6764
Brand: MSI Pages: 96
Xilinx AMS101 User Manual preview
AMS101
Brand: Xilinx Pages: 56
IEI Technology IMBA-BDE-1518-R10 Quick Installation Manual preview
IMBA-BDE-1518-R10
Brand: IEI Technology Pages: 14
Raider Outboards Raider 40 HP Owner'S Manual preview
Raider 40 HP
Brand: Raider Outboards Pages: 73
Tadao Musashi 6 Instructions preview
Musashi 6
Brand: Tadao Pages: 3
Intel D925XEBC2 Product Manual preview
D925XEBC2
Brand: Intel Pages: 74
Fujitsu Siemens Computers D1421 Technical Manual preview
D1421
Brand: Fujitsu Siemens Computers Pages: 20
DFI CS631-C246/Q370 User Manual preview
CS631-C246/Q370
Brand: DFI Pages: 79
Supero SUPER i2DMR-8G2 User Manual preview
SUPER i2DMR-8G2
Brand: Supero Pages: 78
NXP Semiconductors SJA1105SMBEVM User Manual preview
SJA1105SMBEVM
Brand: NXP Semiconductors Pages: 35
NXP Semiconductors LFSTBEB7361 Quick Start Manual preview
LFSTBEB7361
Brand: NXP Semiconductors Pages: 2
Texas Instruments TRS3221RGTEVM User Manual preview
TRS3221RGTEVM
Brand: Texas Instruments Pages: 13
unicore HPL EVK5.0 Installation And Operation User Manual preview
HPL EVK5.0
Brand: unicore Pages: 11

Brands by name

Popular brands

Load more brands