Mitsubishi Electric MELSEC iQ-R RD75P4, Руководство пользователя

Страница: 548 / 598

546
14 TROUBLESHOOTING
14.5 List of Error Codes
1B03H OPR speed
error A value outside the setting range is set in [Pr.46] OPR speed
of OPR basic parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to
 Page 411 [Pr.46]
OPR speed.
1B04H A value set in [Pr.46] OPR speed of OPR basic parameter is
over [Pr.8] Speed limit value.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value so that [Pr.46] OPR speed is equal to or
below [Pr.8] Speed limit value, and turn on PLC READY signal
[Y0].
For details, refer to the following.

Page 389 [Pr.8] Speed limit value

Page 411 [Pr.46] OPR speed
1B05H A value set in [Pr.46] OPR speed of OPR basic parameter is
below [Pr.7] Bias speed at start.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value so that [Pr.46] OPR speed is equal to or
over [Pr.7] Bias speed at start, and turn on PLC READY
signal [Y0].
For details, refer to the following.

Page 386 [Pr.7] Bias speed at start

Page 411 [Pr.46] OPR speed
1B06H Creep speed
error A value outside the setting range is set in [Pr.47] Creep speed
of OPR basic parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to
 Page 412 [Pr.47]
Creep speed.
1B07H A value set in [Pr.47] Creep speed of OPR basic parameter is
over [Pr.46] OPR speed.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value so that [Pr.47] Creep speed is equal to or
below [Pr.46] OPR speed, and turn on PLC READY signal
[Y0].
For details, refer to the following.
 Page 411 [Pr.46] OPR speed
 Page 412 [Pr.47] Creep speed
1B08H A value set in [Pr.47] Creep speed of OPR basic parameter is
below [Pr.7] Bias speed at start.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value so that [Pr.47] Creep speed is equal to or
over [Pr.7] Bias speed at start, and turn on PLC READY
signal [Y0].
For details, refer to the following.

Page 386 [Pr.7] Bias speed at start

Page 412 [Pr.47] Creep speed
1B09H OPR retry error A value outside the setting range is set in [Pr.48] OPR retry of
OPR basic parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to

Page 413 [Pr.48]
OPR retry.
1B0AH Setting for the
movement
amount after
near-point dog
ON error A value outside the setting range is set in [Pr.50] Setting for
the movement amount after near-point dog ON of OPR
detailed parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to
 Page 415 [Pr.50]
Setting for the movement amount after near-point dog ON.
1B0BH OPR
acceleration
time selection
error A value outside the setting range is set in [Pr.51] OPR
acceleration time selection of OPR detailed parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to
 Page 416 [Pr.51]
OPR acceleration time selection.
1B0CH OPR
deceleration
time selection
error A value outside the setting range is set in [Pr.52] OPR
deceleration time selection of OPR detailed parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to

Page 416 [Pr.52]
OPR deceleration time selection.
1B0DH OPR torque limit
value error A value outside the setting range is set in [Pr.54] OPR torque
limit value of OPR detailed parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to

Page 418 [Pr.54]
OPR torque limit value.
1B0EH [Pr.54] OPR torque limit value of OPR detailed parameter is
over [Pr.17] Torque limit setting value of detailed parameter 1.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0].
For details, refer to the following.
 Page 394 [Pr.17] Torque limit setting value

Page 418 [Pr.54] OPR torque limit value
1B0FH Deviation
counter clear
signal output
time setting
error A value outside the setting range is set in [Pr.55] Deviation
counter clear signal output time of OPR detailed parameter.
[Operation of when the error has occurred]
RD75 READY signal [X0] does not turn on. Correct the value within the setting range and turn on PLC
READY signal [Y0]. For details, refer to
 Page 418 [Pr.55]
Deviation counter clear signal output time.
Error
code Error name Cause and description Action