Kubota G2160 Скачать руководство пользователя страница 285

Страница: 285 / 395

9-S12

G2160, WSM

MOWER

Center Pulley Holder

1. Unscrew the center pulley holder screws (2), (14) and / center

pulley nuts (10), (15).

2. Remove the upper oil seal (6) and lower oil seal (5).
3. Remove the internal snap ring (4) and ball bearing (3).
(When reassembling)

• Replace the oil seals (5), (6) with new ones.
• Install the reamer bolt (14) at their original positions as shown in

the figure.

• Be sure to fix the O-rings (11), (12) to the original position.

NOTE

■

• When reassembling the center pulley holder (13), gear box

and gear box stays (7), (8), screw the all screws and nuts by
hand temporary.

• Tighten the screws and nuts in the order as below, to

prevent the incline the gear box.

• Tighten the reamer screws (9) to the gear box first, then

tighten the reamer bolt and nut (10) to the center pulley
holder (13) with specified torque.

• Tighten the gear box screws (1) to the gear box, then tighten

the center pulley holder screws (2), bolt and nut (15) with
specified torque.

W1015291

Tightening torque

Center pulley holder screw
and bolt

77.4 to 90.2 N·m
7.9 to 9.2 kgf·m
57.1 to 66.5 ft-lbs

(1) Gear Box Screw
(2) Center Pulley Holder Screw
(3) Ball Bearing
(4) Snap Ring
(5) Oil Seal
(6) Oil Seal
(7) Gear Box Stay RH
(8) Gear Box Stay LH

(9) Gear Box Reamer Screw

(10) Nut
(11) O-Ring
(12) O-Ring
(13) Center Pulley Holder
(14) Center Pulley Holder Reamer Bolt
(15) Nut

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды