Kubota G2160 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 395

Kubota G2160 Скачать руководство пользователя страница 77

1-S17

G2160, WSM

ENGINE

[2] ENGINE BODY

(1) Checking and Adjusting

Compression Pressure

1. Run the engine until it is warmed up.
2. Stop the engine.
3. Disconnect the 2P connector from the fuel pump.
4. Remove the air cleaner, the muffler and all injection nozzles.
5. Disconnect the accelerator wire.
6. Remove the air cleaner stay.
7. Remove the glow plugs and return hose 1.
8. Engage the parking brake.
9. Set a compression tester (Code No. 07909-30208) with the

adaptor (Adaptor H, Code No. 07909-31231) to the nozzle hole.

10.While cranking the engine with the starter, measure the

compression pressure.

11.Repeat steps 9 and 10 for each cylinder.
12.If the measurement is below the allowable limit, apply a small

amount of oil to the cylinder wall through the nozzle hole and
measure the compression pressure again.

13.If the compression pressure is still less than the allowable limit,

check the top clearance, valve and cylinder head.

14.If the compression pressure increases after applying oil, check

the cylinder wall and piston rings.

NOTE

■

• Check the compression pressure with the specified valve

clearance.

• Always use a fully charged battery for performing this test.
• Variances in cylinder compression values should be under

10

%.

W1022478

Compression pressure

Factory spec.

2.84 to 3.24 MPa
29.0 to 33.0 kgf/cm

2

412 to 469 psi

Allowable limit

2.26 MPa
23.0 kgf/cm

2

327 psi

KiSC issued 11, 2006 A

«
...
75
76
77
78
79
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов