Kubota G2160 Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 395

background image

5-S29

G2160, WSM

STEERING

[3] SERVICING

EPS Controller Right and Left Steering Force Setting at Neutral
Position

IMPORTANT

■

• If this setting procedure is wrongly taken, the neutral

position cannot be programmed in the controller. To take
the procedure over again, be sure to go back to Setting
Method No. 4 (with the main switch at off and the service
connector (1) fit in position).

■

Setting Method

1. Park the machine on level ground.
2. Jack up or lift up the front frame.
3. Using a wooden wedge, etc., prevent the front axle assembly

from oscillating.

4. Turn the steering wheel clockwise and counterclockwise one-

quarter turn each.

5. Turn the front wheels and steering wheel straight ahead (neutral).
6. Turn on the main switch.
7. Disconnect the connector for servicing (1).
8. Turn off the main switch.
9. Connect the connector for servicing (1).

10.Lower the front frame.

IMPORTANT

■

• Do not start the engine while setting.
• Correct setting cannot be made if external force is applied to

the steering wheel during setting.
Therefore take care not to apply external force to the
steering wheel.

■

Check Test

1. Turn on the main switch.
2. Disconnect 1P connector (2) from the oil switch.
3. Turn the steering wheel clockwise and counterclockwise to check

for difference in steering force.

4. If difference in steering force is found, make setting again.
5. Connect the connector to the oil switch.

IMPORTANT

■

• When making setting again, turn off the main switch and

wait or 10 seconds or more before doing so.

• If the connector (2) of the oil switch is left disconnected, a

malfunction could be ceased after starting the engine.

W1023981

Difference in steering
force of steering wheel
between right and left

Factory spec.

Less than 25 %

(1) Connector for Servicing

(2) 1P Connector

KiSC issued 11, 2006 A

«
...
199
200
201
202
203
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2160

Бренд: Daedong Страницы: 238

Бренд: Minsk Tractor Works Страницы: 302

Бренд: Kubota Страницы: 110

Matador 4 x 4 Medium 0853

Бренд: A.E.C. Страницы: 68

Craftsman 944.601901

Бренд: Sears Страницы: 60

Бренд: Winton Страницы: 40

Бренд: Ventrac Страницы: 69

Бренд: Ventrac Страницы: 72

SmarTrax Steering Kit

Бренд: Raven Страницы: 20

Бренд: Valtra Страницы: 414

Бренд: TARAL Страницы: 102

Бренд: KitchenAid Страницы: 6

Бренд: KitchenAid Страницы: 12

Бренд: KitchenAid Страницы: 1

Бренд: KitchenAid Страницы: 12

Бренд: Broan Страницы: 10

Бренд: Yanmar Страницы: 81

Бренд: satoh Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды