manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 96 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 96

1-S36

G2160, WSM

ENGINE

Oil Clearance between Tappet and Tappet Guide Bore

1. Measure the tappet O.D. with an outside micrometer.
2. Measure the I.D. of the tappet guide bore with a cylinder gauge,

and calculate the oil clearance.

3. If the oil clearance exceeds the allowable limit or the tappet is

damaged, replace the tappet.

W11231410

(B) Timing Gears, Camshaft and  Fuel Camshaft

Timing Gear Backlash

1. Set a dial indicator (lever type) with its tip on the gear tooth.
2. Move the gear to measure the backlash, holding its mating gear.
3. If the backlash exceeds the allowable limit, check the oil

clearance of the shaft and the gear.

4. If the oil clearance is proper, replace the gear.

W11264830

Idle Gear Side Clearance

1. Set a dial indicator with its tip on the idle gear.
2. Measure the side clearance by moving the idle gear to the front

and rear.

3. If the measurement exceeds the allowable limit, replace the idle

gear collar.

W11286770

Oil clearance between 
tappet and tappet guide 
bore

Factory spec.

0.016 to 0.052 mm
0.00063 to 0.00205 in.

Allowable limit

0.10 mm
0.0039 in.

Tappet O.D.

Factory spec.

17.966 to 17.984 mm
0.70732 to 0.70803 in.

Tappet guide bore I.D.

Factory spec.

18.000 to 18.018 mm
0.70866 to 0.70937 in.

Backlash between idle 
gear and crank gear

Factory spec.

0.043 to 0.124 mm
0.00169 to 0.00484 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear and cam gear

Factory spec.

0.047 to 0.123 mm
0.00185 to 0.00484 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between idle 
gear and injection pump 
gear

Factory spec.

0.041 to 0.124 mm
0.00161 to 0.00488 in.

Allowable limit

0.15 mm
0.0059 in.

Backlash between oil 
pump drive gear and 
crank gear

Factory spec.

0.041 to 0.123 mm
0.00161 to 0.00484 in.

Allowable limit

0.15 mm
0.0059 in.

Idle gear side clearance

Factory spec.

0.20 to 0.51 mm
0.0079 to 0.0201 in.

Allowable limit

0.60 mm
0.0236 in.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов