manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 214 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 214

6-S5

G2160, WSM

HYDRAULIC SYSTEM

(2) Disassembling and Assembling

(A) Separating Control Valve

Dismount Mower

1. See to “MOWER” section.

W1011842

Draining Transmission Fluid

1. Place an oil pan underneath the drain plug (1).
2. Remove the drain plug (1).
3. Remove the oil inlet plug (2) to completely drain the transmission

fluid.

4. After draining, screw in the drain plug (1) and the oil inlet plug (2).
(When refilling)

• Use the specified transmission fluid.
• Refer  to  “LUBRICANTS, FUEL AND COOLING WATER” (See

Page G-8).

• Never work the machine immediately after changing the

transmission fluid. Keep the engine at medium speed for a few
minutes to prevent damage to the transmission.

W1011896

Seat

1. Disconnect the 2P connector (3) from the seat switch.
2. Remove the seat support mounting lock nuts (1).
3. Remove the guide washers, spring washers and screws (4).
4. Remove the seat bracket (2).
5. Remove the seat with seat support (5).
(When reassembling)

• Turn the seat support mounting lock nuts all the way until it seats

lightly.  Then, turn seat support mounting lock nuts
counterclockwise by a half turn.

• Apply oil to the seat support.
• Face smooth side the plane washers (6) to the seat support.

W1012174

Transmission fluid 
(Including HST cylinder) 

 Capacity

4.5 L
4.8 U.S.qts.
4.0 lmp.qts.

(1) Drain Plug
(2) Oil Inlet Plug 
(3) Oil Level Dipstick

(A) Upper Level
(B) Lower Level

(1) Seat Support Mounting Lock Nuts 
(2) Seat Bracket 
(3) 2P Connector 
(4) Screws

(5) Seat Support
(6) Plane Washers
(7) Fender

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов