Kubota G2160 Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 395

Kubota G2160 Скачать руководство пользователя страница 155

3-S6

G2160, WSM

BRAKE

Separating Pedal System Complete

1. Remove the return spring (3).
2. Pull out the cotter pin (7).
3. Remove the brake rod 2 (6) and plain washer.
4. Disconnect 4P connector (5) from the brake switch (4).
5. Remove the wiring from the pedal system complete.
6. Disconnect the speed change rod (1) from the lever of the pedal

system complete.

7. Remove the pedal system complete mounting screws (2).
8. Remove the pedal system complete.
(When reassembling)

IMPORTANT

■

• Apply grease to the fulcrum of the pedal system complete.
• Adjust the clearance to be between the brake switch and

brake pedal at off position.

• After assembling the speed change rod, be sure to adjust the

length of rod. (See page 2-S5.)

(Reference)

• L : 300 mm (11.8 in.)

W1013572

(2) Brake Assembly

Separating Brake Assembly

1. Pull out the cotter pins (1).
2. Remove the brake rod 3 (5).
3. Remove the brake assembly mounting screws (4).
4. Remove the brake assembly (3) and fulcrum support assembly

(2).

5. Remove the external snap ring (6).
6. Pull out the brake drum (7).
(When reassembling)

• Apply liquid gasket (Three Bond 1208D or its equivalent) to face

of the flange.

• Pushing the brake lever as shown in the figure, tighten the brake

assembly mounting screws.

NOTE

■

• After assembling the brake assembly, be sure adjust the

brake pedal play (See page 3-S2).

W1014378

PEDAL

BRAKE SWITCH

OFF (FREE)

OFF

ON (DEPRESSED)

ON

Tightening torque

Pedal system complete
mounting screw

23.5 to 27.4 N·m
2.4 to 2.8 kgf·m
17.4 to 20.3 ft-lbs

(1) Speed Change Rod
(2) Pedal System Complete Mounting

Screws

(3) Return Spring

(4) Brake Switch
(5) 4P Connector
(6) Brake Rod 2
(7) Cotter Pin

(1) Cotter Pins
(2) Fulcrum Support Assembly
(3) Brake Assembly
(4) Brake Assembly Mounting Screws

(5) Brake Rod 3
(6) External Snap Ring
(7) Brake Drum

KiSC issued 11, 2006 A

«
...
153
154
155
156
157
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов