Kubota G2160 Скачать руководство пользователя страница 277

Страница: 277 / 395

9-S4

G2160, WSM

MOWER

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Checking Mower Blade

1. Check the cutting edge of mower blade.
2. Sharpen the cutting edges, if the mower blades are as shown in

figure (2).

3. Replace the mower blades, if they are as shown in figure (3).

IMPORTANT

■

• Never forget to set the spring plate between mower blade

and spline boss, when reassembling the mower blades.

NOTE

■

• To sharpen the mower blades by yourself, clamp the mower

blade securely in a vise and use a large mill file along the
original level.

• To balance the mower blade, place a small rod through the

center hole and check to see if the blade balances evenly.
File heavy side of the blade until it balances out even.

W1010988

Checking Mower Belts

1. Check to see the mower belts.
2. Replace the mower belt with a new one, if there is found surface

split at more than 3 positions.

(When replacing mower belt)
1. Dismount the mower from the machine.
2. Remove the left and right hand cover (1), (7) from the mower

deck.

3. Clean around the gear case (4) and pulley.
4. Remove the tension springs (7).
5. Remove the L.H. case stay (3) and R.H. case stay (5) which

mounts the gear case to the mower deck.

6. Remove the mower belts (2). Slip the mower belts over the top

of the gear case (4).

7. To install new belts, reverse the above procedure.

W1011170

(1) New Blade
(2) Worn Blade

(3) Cracked Blade

Tightening torque

Reamer bolt

77.4 to 90.2 N·m
7.9 to 9.2 kgf·m
57.1 to 66.5 ft-lbs

(1) L.H. Cover
(2) Mower Belt
(3) L.H. Case Stay
(4) Gear Case

(5) R.H. Case Stay
(6) R.H. Cover
(7) Tension Spring

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды