Kubota G2160 Скачать руководство пользователя страница 333

Страница: 333 / 395

P1-S21

G2460G, WSM

ENGINE

Valves

1. Remove the valve caps (2).
2. Remove the valve spring collet (3), pushing the valve spring

retainer (4) by valve spring replacer (1).

3. Remove the valve spring retainer (4), valve spring (5) and valve

stem seal (6).

4. Remove the valve (7).
(When reassembling)

• Wash the valve stem and valve guide hole, and apply engine oil

sufficiently.

• After installing the valve spring collets, lightly tap the stem to

assure proper fit with a plastic hammer.

IMPORTANT

■

• Don’t change the combination of valve and valve guide.

W1047054

(C) Speed Control Lever and Distributor

Speed Control Plate

1. Remove the screws and copper washers (1) and separate the

speed control plate (2).

(When reassembling)

• Remove the speed control plate (2) and make sure that the

governor lever shaft (4) is correctly set in the governor fork (5).

W1047256

(1) Valve Spring Replacer
(2) Valve Cap
(3) Valve Spring Collet
(4) Valve Spring Retainer

(5) Valve Spring
(6) Valve Stem Seal
(7) Valve

(1) Screws and Copper Washers
(2) Speed Control Plate
(3) Speed Control Plate Cover

(4) Governor Lever Shaft
(5) Governor Fork

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 333 / 395

Результаты поиска

Содержание G2160

Отзывы: