Kubota G2160 Скачать руководство пользователя страница 380 | Manualshive

Страница: 380 / 395

Kubota G2160 Скачать руководство пользователя страница 380

Q6-S5

G2160-R48S, WSM

HYDRAULIC SYSTEM

(C) Separating Grass Collector Cylinder

Separating Grass Collector Cylinder

1. Remove the cylinder cover (3).
2. Pull out the cotter pins (2), (4).
3. Separate the grass collector cylinder (1) from the platform.
4. Remove the adaptors (5), (6) from the grass collector cylinder.
(When reassembling)

• Install the adaptors as shown in the figure.

W1011284

(D) Disassembling Piston Rod Assembly

Piston Rod Assembly

1. Drain hydraulic oil from the cylinder, and secure the tube end of

the cylinder in a vise.

2. Push the flange of the cylinder tube out of the groove of the

cylinder head.

3. Unscrew the cylinder head (1) with a pin key.
4. Pull out the piston rod assembly (2) from the cylinder tube (3).
(When reassembling)

• Visually inspect the cylinder tube for signs of scoring or damage.
• Clean the cylinder tube (3) and piston rod assembly (2).
• Secure the tube end of the cylinder in a vice.
• Insert the piston rod assembly (2) to the cylinder tube (3), after

covering the seal with new hydraulic oil and using care not to
damage the piston seal on the piston.

• Screw the cylinder head (1).
• Push the flange of the cylinder tube inside the groove of the

cylinder head (1) to avoid unlocking.

W1011558

Tightening torque

Adaptor (Grass collector
cylinder)

35.3 N·m
3.6 kgf·m
26.0 ft-lbs

(1) Grass Collector Cylinder
(2) Cotter Pin
(3) Cylinder Cover

(4) Cotter Pin
(5) Adaptor (Grass Collector Cylinder)
(6) Adaptor (Grass Collector Cylinder)
A : 0.79 rad. (45

°

)

Tightening torque

Cylinder head

250 to 300 N·m
25.5 to 30.6 kgf·m
184 to 221 ft-lbs

(1) Cylinder Head
(2) Piston Rod Assembly

(3)Cylinder Tube

KiSC issued 11, 2006 A

«
...
378
379
380
381
382
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов