Kubota G2160 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 395

background image

4-S2

G2160, WSM

FRONT AXLE

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CHECKING AND ADJUSTING

Toe-in

1. Inflate the front tires to the specified pressure.
2. Turn the front wheels straight ahead, and measure the toe-in (B-

A).

3. If the measurement is not within the factory specifications,

change the tie-rod length to adjust.

IMPORTANT

■

• After adjusting the toe-in, secure the tie-rod with the lock

nut.

W1011030

Front Axle End Play

1. Jack up the front of frame.
2. Measure the clearance between the front axle (1) and adjusting

shims (2).

3. If the measurement exceeds the allowable limit, replace the

adjusting shims (2).

(Reference)

• Thickness of adjusting shims:

1.5 mm (0.059 in.) (Part No. K1310-1512-0)
1.9 mm (0.075 in.) (Part No. K1310-1513-0)
2.3 mm (0.091 in.) (Part No. K1310-1514-0)
3.0 mm (0.118 in.) (Part No. K1310-1515-0)

W1011222

Toe-in (B-A)

Factory spec.

0 to 10 mm
0 to 0.394 in.

(A) Wheel to Wheel Distance at Front
(B) Wheel to Wheel Distance at Rear

Front axle end play

Factory spec.

0.1 to 0.4 mm
0.004 to 0.016 in.

Allowable limit

1.0 mm
0.039 in.

(1) Front Axle

(2) Adjusting Shims

KiSC issued 11, 2006 A

«
...
158
159
160
161
162
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2160

COMPACT Vigneto

Бренд: CARRARO Страницы: 296

WEEKEND WARRIOR 6042

Бренд: Maschio Страницы: 46

Бренд: HOLMS Страницы: 9

Бренд: Poulan Pro Страницы: 52

Бренд: R2 RINALDI Страницы: 26

Бренд: Winton Страницы: 12

Бренд: jcb Страницы: 21

Бренд: Valtra Страницы: 21

Бренд: Afron Страницы: 39

Proxima Plus 105

Бренд: Zetor Страницы: 197

PROXIMA PLUS 100 2012

Бренд: Zetor Страницы: 212

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды