Kubota G2160 Скачать руководство пользователя страница 191

Страница: 191 / 395

5-S19

G2160, WSM

STEERING

(4) Torque sensor 3P Connector Terminal

Checking the Resistance of the Torque Sensor 3 Connector
Terminal

1. Using a circuit tester, measure the terminal resistance between

the red and black wires, as well as that between the white and
black wires of torque sensor 3P connector (1).

2. If out of specification replace the power steering assembly with

new one. If the resistance is okay, go to “checking the wire
harness”.

IMPORTANT

■

• Before measuring the resistance, lightly bend the root of the

cable and gently pull it for easy, reliable checking. Be
careful to keep the circuit tester probes tight at the
terminals.

NOTE

■

• The steering wheel turns in different directions on the

broken wires.

W1013879

Resistance
red-black
white-black

Factory spec.

13.0 to 15.0

Problem

Defect

Unexpected turn
clockwise

Red or black wire in poor contact
Black/white wire in poor contact (Harness side)

Unexpected turn
counterclockwise

White wire in poor contact

(1) Torque Sensor 3P Connector
(2) Cable

(a) Red
(b) Black
(c) White

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды