Kubota G2160 Скачать руководство пользователя страница 264

Страница: 264 / 395

8-S24

G2160, WSM

ELECTRICAL SYSTEM

Rectifier

1. Check the continuity across each diode of rectifier with an analog

ohmmeter. Conduct the test in the (R

1) setting.

2. The rectifier is normal if the diode in the rectifier conducts in one

direction and does not conduct in the reverse direction.

IMPORTANT

■

• Do not use a 500 V megger for measuring because it will

destroy the rectifier.

NOTE

■

• Do not use an auto digital multimeter. Because it’s very hard

to check the continuity of rectifier by using it.

W1019720

IC Regulator

1. Check the continuity across the B terminal and the F terminal of

IC regulator with an analog ohmmeter. Conduct the test in the (R

1) setting.

2. The IC regulator is normal if the IC regulator conducts in one

direction and does not conduct in the reverse direction.

IMPORTANT

■

• Do not use a 500 V megger for measuring because it will

destroy the IC regulator.

NOTE

■

• Do not use an auto digital multimeter. Because it’s very hard

to check the continuity of IC regulator by using it.

W1019909

[5] ELECTRICAL EQUIPMENT

CHECKING

(1) Oil Pressure Switch

Oil Pressure Indicator Lamp

1. Disconnect the 1P connector from the oil pressure switch (1).
2. Turn the main switch key to the “ON” position, and connect a

jumper lead from the 1P connector terminal to the chassis.

3. If the oil pressure indicator lamp does not light, the bulb or wiring

harness is faulty.

W1020070

Oil Pressure Switch Continuity

1. Disconnect the 1P connector from the oil pressure switch (1).
2. Measure the resistance with an ohmmeter between the switch

terminal and the chassis.

3. If 0 ohm is not indicated in the normal state, the switch is faulty.
4. If infinity is not indicated at pressure over 4.9 kPa (0.5 kgf/cm

7 psi), the switch is faulty.

W1020184

(1) Oil Pressure Switch

(a) From Oil Pressure indicator Lamp

Resistance
(Switch terminal-
Chassis)

In normal state

0 ohm

At pressure over
approx. 4.9 kPa
(0.5kgf/cm

, 7 psi)

Infinity

(1) Oil Pressure Switch

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды