manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 194 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 194

5-S22

G2160, WSM

STEERING

Checking 16P and 4P Connectors to EPS Controller

1. Disconnect the steering wheel with the steering wheel puller (1)

and puller adaptror (2) carefully.  Do not use any hammer.

2. Detach panel and make the following check.  with the main switch

at ON position (do not start the engine), measure the voltages
between following terminals.

3. Measuring the voltage at the 16P connector (6) with the main

switch at ON position (do not start the engine), measure the
voltage between the black (3), (4) and red/white (7) terminals.

4. Measuring the voltage at the 4P connector (8) with the main

switch at OFF position, measure the voltage between the green
(11) and black (12) terminals.

IMPORTANT

■

• While disassembling, handle the power steering assembly,

controller and wire harness with enough care.  To
disconnect the steering wheel, be sure to use the steering
wheel puller, never any hammer.
Excessive load or impact on the parts may result in trouble.

• To disconnect the connector, press the connector's lock

and hold the connector itself.  Never pull the cable.

Controller 4P Connector

W1016611

(11)

Green

Battery (+)

(10)

Blue

Motor (+)

(12)

Black

GND

(9)

Black / white

Motor (-)

(1) Steering Wheel Puller
(2) Puller Adaptor
(3) Black Terminal (GND)
(4) Black Terminal (GND)
(5) Notch
(6) EPS Controller 16P Connector (view 

from the wire-connected side)

(7) Red/white Terminal
(8) Controller 4P Connector (view from 

        the wire-connected side)

(9) Black/white Terminal

(10) Blue Terminal

(11) Green Terminal

(12) Black Terminal

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов