Kubota G2160 Скачать руководство пользователя страница 78

Страница: 78 / 395

1-S18

G2160, WSM

ENGINE

Top Clearance

1. Remove the cylinder head (Do not attempt to remove the cylinder

head gasket completely).

2. Bring the piston to its top dead center fasten 1.5 mm dia. 5 to 7

mm long fuse wires to 3 to 4 spots on the piston top with grease
so as to avoid the intake and exhaust valves and the combustion
chamber ports.

3. Bring the piston to its middle position, install the cylinder head,

and tighten the cylinder head screws to specification. (Head
gasket must be changed to new one.)

4. Turn the crank shaft until the piston exceeds its top dead center.
5. Remove the cylinder head, and measure the thickness of the

squeezed fuses.

6. If the measurement is not within the factory specifications, check

the oil clearance of between the crankpin and crankpin bearing
and between the piston pin and small end bushing.

NOTE

■

• After checking the top clearance, be sure to assemble the

cylinder head with a new cylinder head gasket.

W10107670

Top clearance

Factory spec.

0.50 to 0.70 mm
0.0197 to 0.0276 in.

Tightening torque

Cylinder head bolt

37.2 to 42.1 N·m
3.8 to 4.3 kgf·m
28.0 to 31.7 ft-lbs

(1) Fuse

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды