manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 197 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 197

5-S25

G2160, WSM

STEERING

[2] DISASSEMBLING  AND  ASSEMBLING

(1) Separating Power Steering Assembly and EPS Controller

Battery and Bonnet

1. Turn the main switch off.
2. Remove the radiator screen (1).
3. Disconnect the negative cable from the battery.
4. Disconnect the 1P connectors (3) from the head light (2).
5. Remove the wiring (4) from the bonnet.
6. Remove the bonnet stay mounting screws (6), and remove the

bonnet with the bonnet bracket (5) from the frame.

W1020278

Wiring

1. Remove the indicator lamps (4).
2. Disconnect 1P connector (3) from the hour meter.
3. Disconnect 1P connector (1) from the light switch.
4. Disconnect 4P connector (2) from the main switch.

W1020553

Parking Lock Pedal

1. Remove the parking lock pedal mounting nut (2).
2. Remove the parking lock pedal (1) from the brake lock.
(When reassembling)

IMPORTANT

■

• Using the oval hole, make such adjustment that he parking

lock pedal be kept out of contact with the panel over the
entire stroke.

• Step on the brake pedal and parking lock pedal at once, and

make sure that the speed change pedal gets locked.

• If the speed change pedal fails to get locked, set this pedal

to the neutral position and readjust the brake lock (3) so that
the lock pin (5) comes into the notch (4).

W1020703

(1) Radiator Screen
(2) Head Light 
(3) 1P Connectors

(4) Wiring
(5) Bonnet Bracket
(6) Bonnet Stay Mounting Screws

(1) 1P Connector
(2) 4P Connector

(3) 1P Connector
(4) Indicator Lamp

(1) Parking Lock Pedal
(2) Parking Lock Pedal Mounting Nut
(3) Brake Lock

(4) Notch
(5) Lock Pin

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов