Kubota G2160 Скачать руководство пользователя страница 308

Страница: 308 / 395

PG-11

G2460G, WSM

G GENERAL

[6] CHECK POINTS OF EVERY 1 YEAR

Flushing Cooling System and Changing Coolant

CAUTION

• Never open radiator cap when engine is hot.
• When opening, loosen cap slightly to the stop to relieve any

excess pressure before removing radiator cap completely.

1. Stop the engine and let cool down.
2. To drain the coolant, open the radiator drain plug (3) and engine

drain cock (4) and remove the radiator cap (1). The radiator cap
(1) must be removed to completely drain the coolant.

3. After all coolant is drained, fill with clean water and cooling

system cleaner.

4. Follow directions of the cleaner instruction.
5. After flushing, fill with clean water and anti-freeze until the coolant

level is just below the port.

6. Fill with clean water and anti-freeze upper level of the recovery

tank (2).

7. Start and operate the engine for few minutes.
8. Stop the engine. Check coolant level and add coolant if

necessary.

9. Install the radiator cap (1) securely.

W1037404

Replacing Fuel Line

1. Replace the fuel hoses (2) and hose clamps (1).

Refer to “Checking Fuel Line”. (See page PG-7.)

W1038054

(1) Radiator Cap
(2) Recovery Tank
(3) Radiator Drain Plug
(4) Engine Drain Cock

A : Highest Level
B : Lowest Level

(1) Hose Clamp

(2) Fuel Hose

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды