manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 85 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 85

1-S25

G2160, WSM

ENGINE

Fuel Camshaft

1. Remove the screws and draw out the camshaft with the gear on

it.

2. Remove the retaining plate (1).
3. Remove the screws, then draw out the injection pump gear (2)

and fuel camshaft (3) with the governor fork assembly.

(When reassembling)

• Hook the spring to the fork lever 2 (4) as shown in the figure

before installing the fork lever assembly to the crankcase.

W10178820

Oil Pump and Crankshaft Gear

1. Remove the oil pump gear (6).
2. Remove the oil pump (5).
3. Remove the collar (4), O-ring (3) and oil slinger (2).
4. Remove the crankshaft gear (1) with a puller.
(When reassembling)

• Install the collar after aligning the marks on the gears. (See the

figure at “Idle Gear”.)

W10180290

(1) Retaining Plate
(2) Injection Pump Gear
(3) Fuel Camshaft

(4) Fork Lever 2
(5) Fork Lever 1
(6) Governor Sleeve

(1) Crankshaft Gear
(2) Crankshaft Oil Slinger
(3) O-ring

(4) Crankshaft Collar
(5) Oil Pump
(6) Oil Pump Gear

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов