Kubota G2160 Скачать руководство пользователя страница 381 | Manualshive

Страница: 381 / 395

Kubota G2160 Скачать руководство пользователя страница 381

Q6-S6

G2160-R48S, WSM

HYDRAULIC SYSTEM

Cylinder Head, Piston and Nut

1. Secure the rod end in a vise.
2. Unscrew the cylinder piston mounting lock nut (4).
3. Remove the piston (3) and cylinder head (2) from the piston rod

(1).

(When reassembling)

• Visually inspect all parts for signs of scoring or damage.
• Secure the rod end in a vice.
• Install the cylinder head (2) with seals mounted on the piston rod

(1).

• Install the piston (3) with seals mounted on the piston rod (1).
• Screw the cylinder piston mounting lock nut (4).

W1011806

Installing Piston Seal

NOTE

■

• The piston seal doesn't need any particular tool to install.

1. Clean all components and check if anything is inside the grooves.
2. Check the sliding seal surfaces are clean and without damage.
3. Install the O-ring (2) inside the internal groove of the piston (3)

without twisting it.

4. Install the internal black square part of the piston seals (1) inside

the external groove of the piston (3), while checking it is not twist.

5. Using a tool (like a screwdriver) without any sharp edges, install

the blue external part of the piston seals (1) above the black part.

W1012170

Installing Cylinder Head Seal

NOTE

■

• The cylinder head seal doesn't need any particular tool to

install.

1. Clean all components and check if anything is inside the groove.
2. Check the sliding seal surfaces are clean and without damage.
3. Install the wiper seal (1) inside the internal groove of the cylinder

head (2).

NOTE

■

• Check the wiper seal is toward the inside of the cylinder.

4. Install the O-ring (3) against dust between the flange stopper of

the cylinder head (2) and the thread.

5. Install the O-ring (5) and anti-extrusion collar (4) in the external

groove of the cylinder head (2), by respecting their position: O-
ring on oil seal, and collar on thread side.

W1012369

Tightening torque

Cylinder piston mounting
lock nut

300 to 350 N·m
30.6 to 35.7 kgf·m
221 to 258 ft-lbs

(1) Piston Rod
(2) Cylinder Head

(3) Piston
(4) Cylinder Piston Mounting Lock Nut

(1) Piston Seal
(2) O-ring

(3) Piston

(1) Wiper Seal
(2) Cylinder Head
(3) O-ring

(4) Anti-extrusion Collar
(5) O-ring

KiSC issued 11, 2006 A

«
...
379
380
381
382
383
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов