manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 110 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 110

1-S50

G2160, WSM

ENGINE

(2) Disassembling and Assembling

Thermostat Assembly

1. Remove the thermostat cover mounting screws, and remove the

thermostat cover (1).

2. Remove the thermostat assembly (3).
(When reassembling)

• Apply a liquid gasket (Three Bond 1215 or equivalent) only at the

thermostat cover side of the gasket (2).

W10393690

Water Pump Assembly

1. Loosen the alternator mounting bolts, and remove the fan belt.
2. Remove the fan and fan pulley.
3. Remove the water pump assembly from the gear case cover.
4. Remove the water pump flange (1).
5. Press out the water pump shaft (2) with the impeller (5) on it.
6. Remove the impeller from the water pump shaft (2).
7. Remove the mechanical seal (4).
(When reassembling)

• Apply a liquid gasket (Three Bond 1215 or equivalent) to the both

sides of gasket.

• Replace the mechanical seal with new one.

W10395040

(1) Thermostat Cover
(2) Thermostat Cover Gasket

(3) Thermostat Assembly

(1) Water Pump Flange
(2) Water Pump Shaft
(3) Water Pump Body

(4) Mechanical Seal
(5) Impeller

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов