Kubota G2160 Скачать руководство пользователя страница 113

Страница: 113 / 395

1-S53

G2160, WSM

ENGINE

(B) Injection Nozzle

CAUTION

• Check the injection pressure and condition after confirming that there is nobody standing in the direction

the fume goes.
If the fume from the nozzle directly contacts the human body, cells may be destroyed and blood poisoning
may be caused.

Nozzle Spraying Condition

1. Set the injection nozzle to a nozzle tester (Code No. 07909-

31361), and check the nozzle spraying condition.

2. If the spraying condition is defective, replace the nozzle piece.

W10411400

Fuel Injection Pressure

1. Set the injection nozzle to a nozzle tester (Code No. 07909-

31361).

2. Slowly move the tester handle to measure the pressure at which

fuel begins to jet out from the nozzle.

3. If the measurement is not within the factory specifications,

replace the adjusting washer (1) in the nozzle holder to adjust it.

(Reference)

• Pressure variation with 0.025 mm (0.001 in.) difference of

adjusting washer thickness.
Approx. 59 kPa (0.6 kgf/cm

, 8.5 psi)

W10408820

Valve Seat Tightness

1. Set the injection nozzle to a nozzle tester (Code No. 07909-

31361).

2. Raise the fuel pressure, and keep at 12.7 MPa (130 kgf/cm

1850 psi) for 10 seconds.

3. If any fuel leak is found, replace the nozzle piece.

W10412730

(a) Good

(b) Bad

Fuel injection pressure

Factory spec.

13.7 to 14.7 MPa
140 to 150 kgf/cm

1990 to 2130 psi

(1) Adjusting Washer

Valve seat tightness

Factory spec.

No fuel leak at
12.7 MPa
130 kgf/cm

1850 psi

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 113 / 395

Результаты поиска

Содержание G2160

Отзывы: