Kubota G2160 Скачать руководство пользователя страница 212

Страница: 212 / 395

6-S3

G2160, WSM

HYDRAULIC SYSTEM

4. CHECKING, DISASSEMBLING AND SERVICING

[1] CONTROL VALVE

(1) Checking and Adjusting

Main Relief Valve Setting Pressure

CAUTION

• When checking, park the tractor on flat ground, apply the

parking brake.

1. Disconnect the cylinder hose from the mower lift cylinder.
2. Set the adaptor for control valve (see page G-39.), thread joint

(Code No.: 07916-50341), cable (Code No.: 07916-50331),
thread joint (Code No.: 07916-50401) and pressure gauge 50
(Code No.: 07916-52961).

3. Start the engine and run the engine speed at rated speed.
4. Move the mower control lever to “LIFT” position to operate the

main relief valve.

5. Read the pressure gauge.
6. If the pressure is not within the factory specifications, adjust with

the adjusting shims.

Condition

• Engine Speed.....Rated speed
• Oil Temperature..40 to 50

C (104 to 122

IMPORTANT

■

• Measure quickly so that the man relief valve may not be in

operation more than 10 seconds.

(Reference)

• Thickness of adjusting shims:

0.2 mm (0.008 in.) (Part No.: 48100-36280)
0.3 mm (0.012 in.) (Part No.: 48100-36270)

W1010979

Main relief valve setting
pressure

Factory spec.

2.94 to 3.43 MPa
30.0 to 35.0 kgf/cm

426 to 497 psi

(1) O-ring
(2) Poppet
(3) Spring

(4) Shims
(5) Plug
(6) Main Relief Valve

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды