Kubota G2160 Скачать руководство пользователя страница 303 | Manualshive

Страница: 303 / 395

background image

PG-6

G2460G, WSM

G GENERAL

[2] CHECK POINTS OF INITIAL 50 HOURS

Changing Engine Oil

CAUTION

• Be sure to stop the engine before changing oil.

1. Start and warm up the engine for approx. 5 minutes.
2. Place an oil pan underneath the engine.
3. To drain the used oil, remove the drain plug (1) at the bottom of

the engine and drain the oil completely.

4. Screw in the drain plug (1).
5. Fill new oil up to upper line on the dipstick (3).

IMPORTANT

■

• When using an oil of different manufacture or viscosity from

the previous one, remove all of the old oil.

• Never mix two different type of oil.
• Use the proper SAE engine oil according to ambient

temperatures.
Refer to “LUBRICANTS, FUEL AND COOLANT”.
(See page PG-2.)

W1030749

Replacing Engine Oil Filter Cartridge

CAUTION

• Be sure to stop the engine before changing the oil filter

cartridge.

• Allow engine to cool down sufficiently, oil can be hot and

may cause burns.

1. Remove the engine oil filter cartridge (1) with the filter wrench.
2. Apply a slight coat of oil onto the rubber gasket of new cartridge.
3. To install the new cartridge, screw it in by hand. Over tightening

may cause deformation of rubber gasket.

4. After the cartridge has been replaced, the engine oil level

normally lowers a little. Add engine oil to proper level. Check for
oil leaks around filter gasket.

IMPORTANT

■

• To prevent serious damage to the engine, element of

recommended type must be used. Use only a genuine
KUBOTA filter or its equivalent.

W1030950

(1) Drain Plug
(2) Oil Inlet Plug
(3) Dipstick

(A) Upper Level
(B) Lower Level

(1) Engine Oil Filter Cartridge

KiSC issued 11, 2006 A

«
...
301
302
303
304
305
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2160

Бренд: Glasdon Страницы: 2

Бренд: Claas Страницы: 31

Бренд: Troy-Bilt Страницы: 44

Бренд: Vari Страницы: 9

HORTUS HS Series

Бренд: Zetor Страницы: 142

Бренд: Mahindra Страницы: 92

Бренд: Mahindra Страницы: 90

Бренд: Mahindra Страницы: 94

Cropmaster VAK1 Series

Бренд: David Brown Страницы: 51

Бренд: Viking Страницы: 7

Бренд: Holder Страницы: 4

Бренд: Holder Страницы: 87

Бренд: Struck Страницы: 24

Magnatrac RS1000

Бренд: Struck Страницы: 117

Бренд: KNEGT Страницы: 73

Бренд: KNEGT Страницы: 103

Бренд: KNEGT Страницы: 105

WHEATHEART X130

Бренд: AGI Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды