Kubota G2160 Скачать руководство пользователя страница 141

Страница: 141 / 395

2-S19

G2160, WSM

TRANSMISSION AND REAR AXLE

Trunnion Arm and Journal Bearing

1. Remove the trunnion arm (1).
2. Pry the oil seal (3) off with a screwdriver.
3. Press out the journal bearing (2).
(When reassembling)

• Apply clean field to the journal bearing.

NOTE

■

• Take care not to damage the housing.

W1031388

(B) Transmission

Brake Assembly

1. Remove the brake assembly mounting screws (3).
2. Remove the brake assembly (2) with the fulcrum support

assembly (1).

3. Remove the external snap ring (4).
4. Pull out the brake drum (5).
(When reassembling)

• Apply liquid gasket (Three Bond 1208D or its equivalent) to face

of the flange.

• Pushing the brake lever (6) as shown in the figure, tighten the

brake assembly mounting screws.

NOTE

■

• After assembling the brake assembly, be sure to adjust the

brake pedal play (See page G-19).

W1031669

(1) Trunnion Arm
(2) Journal Bearing

(3) Oil Seal

(1) Fulcrum Support Assembly
(2) Brake Assembly
(3) Brake Assembly Mounting Screws

(4) External Snap Ring
(5) Brake Drum
(6) Brake Lever

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 141 / 395

Результаты поиска

Содержание G2160

Отзывы: