Kubota G2160 Скачать руководство пользователя страница 257

Страница: 257 / 395

8-S17

G2160, WSM

ELECTRICAL SYSTEM

SERVICING

(1) Starter

Commutator and Mica

1. Check the contact face of the commutator for wear, and grind the

commutator with emery paper if it is slightly worn.

2. Measure the commutator O.D. with an outside micrometer at

several points.

3. If the minimum O.D. is less than the allowable limit, replace the

armature.

4. If the difference of the O.D.’s exceeds the allowable limit, correct

the commutator on a lathe to the factory specification.

5. Measure the mica undercut.
6. If the undercut is less than the allowable limit, correct it with a saw

blade and chamfer the segment edges.

W1015371

Brush Wear

1. If the contact face of the brush is dirty or dusty, clean it with emery

paper.

2. Measure the brush length (A) with vernier calipers.
3. If the length is less than the allowable limit, replace the yoke

assembly and brush holder.

W1015798

Brush Holder

1. Check the continuity across the brush holder and the holder

support with an ohmmeter.

2. If it conducts, replace the brush holder.

W1015919

Commutator O.D

Factory spec.

28.0 mm
1.102 in.

Allowable limit

27.0 mm
1.063 in.

Difference of O.D.'s

Factory spec.

Less than 0.02 mm
Less than 0.0008 in.

Allowable limit

0.05 mm
0.0020 in.

Mica undercut

Factory spec.

0.60 mm
0.0236 in.

Allowable limit

0.20 mm
0.0079 in.

(1) Segment
(2) Undercut
(3) Mica

(a) Correct
(b) Incorrect

Brush length (A)

Factory spec.

14.0 mm
0.551 in.

Allowable limit

11.1 mm
0.437 in.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 257 / 395

Результаты поиска

Содержание G2160

Отзывы: