manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 283 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 283

9-S10

G2160, WSM

MOWER

[3] DISASSEMBLING  AND  ASSEMBLING

Universal Joint and Covers

1. Remove the universal joint.
2. Remove the left and right hand covers (1), (2).
(When reassembling)

• Apply grease to the splines and grease nipples of the universal

joint.

W1013857

Mower Blades (Center Blade and Outer Blades)

1. Turn over the mower.
2. Unscrew the mower blade screw (5), and remove the spline boss

(4), two cup washers (3), mower blade (2) and dust cover (1).

NOTE

■

• To remove the blade securely, wedge a block of wood

between one blade and the mower deck in such position that
it will hold the blade safely while loosing or tightening the
blade screw.

(When reassembling)

• Be sure to assemble the two cup washers between the mower

blade and lock washer or spline boss.

IMPORTANT

■

• Make sure the cup washer is not flattened out or worn,

causing blade to slip easily.
Replace two cup washers if either is damaged.

W1013987

(1) L.H. Cover

(2) R.H. Cover

Tightening torque

Mower blade screw

98.1 to 117.7 N·m
10.0 to 12.0 kgf·m
72.3 to 86.8 ft-lbs

(1) Dust Cover
(2) Mower Blade
(3) Cup Washer
(4) Lock Washer
(5) Mower Blade Screw
(6) Spline Boss

(A) Loosen

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов