manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 168 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 168

5-M3

G2160, WSM

STEERING

(2) Torque Sensor

■

Construction

The torque sensor senses the steering power and

rotating direction, convert them into a voltage signal and
outputs the signal to the EPS controller.  The torque
sensor section is composed of a slider (3), detecting ring
and detecting coil (4) (slider and detecting ring are
combined).  The slider (3) is held by the slider pin (2)
connected to the input shaft (1) and output shaft (5).  
A thread groove and longitudinal groove (in the axial
direction) are provided on the inside of the slider.  The
relative change of the rotating direction of the input shaft
(1) and output shaft (5) is converted into a movement in
the slider axial direction.

W1013290

■

Operation

W1013543

When a torsion torque is generated via the torsion bar

between the input shaft (1) and output shaft (5) as a
result of the steering wheel being turned, the input-shaft-
side slider pin moves along the thread groove of the
slider and makes the slider shift in the axial direction.
The slider shifting direction and distance are detected as
the amount of electrical change between the detecting
ring and detecting coil and transmitted to the EPS
controller.

W1013984

(1) Input shaft
(2) Slider Pin
(3) Slider

(4) Detecting Ring and Detecting 

Coil

(5) Output Shaft

(1) Input Shaft
(2) Slider Pin
(3) Slider
(4) Detecting Ring and Detecting Coil
(5) Output Shaft

A : Steering wheel turned counterclockwise
B : Steering wheel in neutral position
C : Steering wheel turned clockwise
D : 1 mm (0.04 in.)

A : Torque Sensor Output
B : Output Voltage (V)
C : Voltage

D : Steering Direction
E : Left
F : Right

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов