Kubota G2160 Скачать руководство пользователя страница 163

Страница: 163 / 395

4-S5

G2160, WSM

FRONT AXLE

Knuckle Arm and Kingpin

1. Remove the knuckle arm mounting bolt (3), spring washer and

nut (5).

2. Remove the knuckle arm (4) and the kingpin (L.H.) (6).
3. Remove the external snap ring (1) and kingpin (R.H.) (2).
(When reassembling)

• Apply grease to the kingpins.

W1012736

(3) Disassembling Front Axle Support Assembly

Front Axle Support Assembly

1. Remove the internal snap ring (2).
2. Tap out the PTO shaft (1) forward.
(When reassembling)

• Replace the oil seal with a new one.
• Apply grease to the oil seal lip, and take care that it is not rolled

when installing the PTO shaft.

W1013054

[3] SERVICING

Clearance between Front Axle and Front Axle Support

1. Measure the front axle I.D. with a cylinder gauge.
2. Measure the front axle support O.D. with an outside micrometer,

and calculate the clearance.

3. If the clearance exceeds the allowable limit, replace them.

W1013254

Tightening torque

Knuckle arm mounting bolt

48.0 to 55.9 N·m
4.9 to 5.7 kgf·m
35.4 to 41.2 ft-lbs

(1) External Snap Ring
(2) Kingpin (R.H.)
(3) Knuckle Arm Mounting Bolt

(4) Knuckle Arm
(5) Knuckle Arm Mounting Nut
(6) Kingpin (L.H.)

(1) PTO Shaft
(2) Internal Snap Ring
(3) Ball Bearing
(4) External Snap Ring

(5) Needle Bearing
(6) Oil Seal
(7) Front Axle Support

Clearance between front
axle and front axle
support

Factory spec.

0.025 to 0.089 mm
0.00098 to 0.00350 in.

Allowable limit

0.30 mm
0.0118 in.

Front axle I.D.

Factory spec.

40.000 to 40.039 mm
1.57480 to 1.57634 in.

Front axle support O.D.

Factory spec.

39.950 to 39.975 mm
1.57283 to 1.57382 in.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды