manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 305 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 305

PG-8

G2460G, WSM

G  GENERAL

Checking Spark Plugs

1. Lift hood.
2. Remove the spark plug wire from spark plug (1).
3. Use a spark plug wrench to remove plug (1).

NOTE

■

• This engine is equipped with resistor-type spark plugs.

4. Inspect spark plugs (1) for cracked porcelain, pitted electrodes,

or other wear and damage.  Replace spark plugs if necessary.

5. Check spark plug gap (A) with a feeler gauge.
6. If the spark plug gap (A) is not factory specification, adjust the

spark plug gap (A).

7. NGK BKR4E-11 spark plug is recommended.

W1022501

Checking Battery Condition

CAUTION

• Never remove the vent cap while the engine is running.

Keep electrolyte away from eyes, hands and clothes.  If you
are spattered with it, wash it away completely with water
immediately and get medical attention.

• Wear eye protection and rubber gloves when working

around battery.
Mishandling the battery shortens the service life and adds to
maintenance costs.
The original battery is a maintenance-free, non accessible type
battery.

W1027816

Spark plug gap (A)

Factory spec.

1.1 mm 
0.043 in.

(1) Spark Plug

(A) Spark Plug Gap

(1) Battery

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов