manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 260 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 260

8-S20

G2160, WSM

ELECTRICAL SYSTEM

[4] CHARGING  SYSTEM

CHECKING

(1) Alternator

Alternator

1. Disconnect the 2P connector (3) from alternator (2) after tuning

the main switch OFF.

2. Perform the following checkings.

W1017030

Connector Voltage

1. Turn the main switch OFF. Measure the voltage between the B

terminal (1) and the chassis.

2. Turn the main switch ON. Measure the voltage between the IC

terminal (3) and the chassis.

W1017151

No-Load Test

1. Connect the 2P connector (6) to previous positions of the

alternator after turning the main switch OFF.

2. Connect the jumper lead (3) between IG terminal (4) and B

terminal (2).

3. Start the engine and then set the idling speed.
4. Disconnect the negative cable from the battery.
5. Measure the voltage between the B terminal (2) and the chassis.
6. If the measurement is less than the factory specification,

disassemble the alternator and check the IC regulator.

(Reference)

• Once the engine has started, the altinator temperature rises

quickly up to an ambient temperature of 70 to 90 

°

C (158 to 194

°

F). As the temperature goes higher than 50 

°

C (122 

°

F), the

alternator voltage slowly drops; at higher than 100 

°

C (212 

°

F), it

drops by about 1 V.

W1017349

(1) B Terminal 
(2) Alternator

(3) 2P Connector 

Voltage 
(Main switch at OFF)

B Terminal - Chassis

Approx. battery voltage

Voltage
(Main Switch at ON)

IG terminal - Chassis

Approx. battery voltage

(1) B Terminal
(2) Alternator

(3) IG Terminal
(4) L Terminal

Voltage

Factory spec.

More than 14V

(1) Voltmeter
(2) B Terminal
(3) Jumper Lead

(4) IG Terminal
(5) L Terminal
(6) 2P Connector

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов