Kubota G2160 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 395

background image

2-S10

G2160, WSM

TRANSMISSION AND REAR AXLE

Separating Fender

1. Remove the speed change pedal.
2. Peel the step sheet (1) halfway.
3. Remove the step support mounting screws (2).
4. Remove the step support (5) and rubber bushing (6).
5. Remove the fuel cap (4).
6. Separate the fender from the frame.
(When reassembling)

• Apply grease to the inside of rubber bushing.
• Clean up the step sheet and the step. Apply instantaneous

adhesive on the step sheet as shown in the figure.

• Position the step sheet so that the clearance between the step

sheet and the panel is less than 2.0 mm (0.079 in.) as shown in
the figure.

W1018335

(D) Separating Transmission

Upper Lift Link and Link Assembly

1. Pull out the rue ring cotters (3) and plain washers.
2. Remove the upper lift links (4).
3. Pull out the cotter pin (1) and plain washer.
4. Remove the L.H. rear link assembly (2).
5. Remove the R.H. rear link assembly retaining lock nut and bolt.
6. Remove the R.H. rear link assembly.
(When reassembling)

• Apply the grease to the rotary sliding surface.
• Adjust the upper lift link and lower lift link referring to the

“MOWER” section.

IMPORTANT

■

• Tighten the R.H. rear link assembly lock nut and bolt, leaving

as little gap as possible between the frame and the lock nut.
Also be sure that the rear link assembly turns smoothly.

(Reference)

• L : 350mm (13.8 in.)

W1015243

(1) Step Sheet
(2) Step Support Mounting Screws
(3) Fuel Cap
(4) Step Support
(5) Rubber Bushing

(A) Less than 2.0mm (0.079 in.)
(B) Panel

(1) Cotter Pin
(2) L.H. Rear Link Assembly
(3) Rue Ring Cotter

(4) Upper Lift Link
(5) Lower Lift Link

KiSC issued 11, 2006 A

«
...
130
131
132
133
134
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2160

Бренд: Rankin Страницы: 37

Бренд: Sears Страницы: 24

Бренд: Fort Страницы: 80

Бренд: Stow Страницы: 70

Бренд: Mahindra Страницы: 92

Бренд: CAMSO Страницы: 29

Бренд: Electrolux Страницы: 2

Бренд: Worksaver Страницы: 40

Бренд: Vestil Страницы: 11

Бренд: Summit Страницы: 35

Бренд: New Holland Страницы: 41

Бренд: mecalac Страницы: 19

Бренд: BCS Страницы: 66

Бренд: BCS Страницы: 99

Бренд: BCS Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды