Kubota G2160 Скачать руководство пользователя страница 278 | Manualshive

Страница: 278 / 395

background image

9-S5

G2160, WSM

MOWER

Adjusting the Parallel Linkage

1. Park the machine on a level surface.
2. Make sure the mower blades are level in the way mentioned

below. Then tighten the lock nuts securely.
Adjust (L) of front rinks with lock nut so that (A) is 0

∼

5 mm (0

∼

0.2

in.). A=(Y)-(X)

CAUTION

• Shut off the engine and remove the key.
• Set parking brake.
• Allow the blades to stop before making adjustments.
• Blades may be sharp, when you handle blades, wear heavy

gloves or wrap end of blade with rag.

W1011500

Adjusting the Mower Deck (Side-to-Side)

1. Park the machine on a level surface.
2. Tire inflation pressure must be correct.

(See “TIRE” section.)

3. Raise the hydraulic lift lever to the top position. Turn the cutting

height control dial to adjust height to the desired height.

4. Lower the mower deck by pushing the hydraulic lift lever forward.
5. Turn the left blade so that it is parallel to rear axle.

Hold drive belt and turn the right blade so that it is parallel to axle.

6. Measure from each outside blade tip (L) to (R) to the level

surface. The difference between measurements should be less
than 1/8 in. (3 mm).

7. Remove the snap ring, plain washer and clevis pin. Adjust the lift

link length so that the difference between measurement (L) and
(R) is less than 1/8 in. (3 mm).

8. Reinstall the snap ring, plain washer and clevis pin.

CAUTION

• Shut off the engine and remove the key.
• Set parking brake.
• Allow the blades to stop before making adjustments.
• Blades may be sharp. When you handle blades, wear heavy

gloves or wrap end of blade with a rag.

W1011782

(1) Lift Link (Upper)
(2) Lift Link (Lower)
(3) Snap Ring

(4) Plane Washer
(5) Clevis Pin

KiSC issued 11, 2006 A

«
...
276
277
278
279
280
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2160

Бренд: Nakayama Страницы: 24

Бренд: Ford Страницы: 41

Бренд: JOSEPH JOSEPH Страницы: 9

Бренд: Broan Страницы: 44

Бренд: townew Страницы: 8

Бренд: Toyama Страницы: 60

Бренд: Valtra Страницы: 41

Бренд: Yanmar Страницы: 6

Бренд: Yanmar Страницы: 170

Бренд: Bush Hog Страницы: 38

Бренд: New Holland Страницы: 412

Бренд: Kioti Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды