Kubota G2160 Скачать руководство пользователя страница 348

Страница: 348 / 395

P8-S3

G2460G, WSM

ELECTRICAL SYSTEM

[2] SOLENOID CHECKING

Fuel Cut Off Solenoid

1. Disconnect the connector.
2. Measure the resistance with an ohmmeter between the

connector terminals.

3. If the factory specification is not indicated the solenoid is faulty.

W1088666

[3] HIGH TENSION CORD CHECKING

High Tension Cord

1. Using an ohmmeter, check that the resistance does not exceed

the maximum.

2. If more than maximum, check the terminals, and replace the

high-tension cord and / or distributor cap as required.

W1088824

Ignition Timing

1. Using a timing light, check that the ignition timing (stamps on the

flywheel) (5) is aligned with the mark (3) on the rear end plate (2).

2. If the timing is wrong, loosen the distributor mounting screw (6)

and turn the distributor (7) so that the ignition timing (stamps on
the flywheel) is aligned with the mark on the rear end plate.
(See page P1-S22.)

W1090028

Resistance

Factory spec.

Approx. 38

(1) Gasoline Stop Solenoid

Resistance

High tension
cord #1

Engine serial No.:
below YY8644

2.47 to 4.21 k

Engine serial No.:
above 1A0001

2.81 to 4.79 k

High tension
cord #2

Engine serial No.:
below YY8644

2.98 to 5.08 k

Engine serial No.:
above 1A0001

3.40 to 5.80 k

High tension
cord #3

Engine serial No.:
below YY8644

3.15 to 5.37 k

Engine serial No.:
above 1A0001

3.57 to 6.09 k

Center cord

3.06 to 5.22 k

Ignition timing

Factory spec.

0.32 rad. (18

) before

T.D.C.

(1) Flywheel
(2) Rear End Plate
(3) Mark
(4) Ignition Timing
(5) Distributor Mounting Screw
(6) Distributor

(A) To retard
(B) To advance

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 348 / 395

Результаты поиска

Содержание G2160

Отзывы: