Kubota G2160 Скачать руководство пользователя страница 227

Страница: 227 / 395

7-S6

G2160, WSM

PTO SYSTEM

[3] SERVICING

Clearance between Tension Collar and Tension Arm Bushing

1. Measure the tension collar O.D. with an outside micrometer.
2. Measure the tension arm bushing I.D. with an inside micrometer,

and calculate the clearance.

3. If the clearance exceeds the allowable limit, replace the tension

arm bushing.

4. If the clearance still exceeds the allowable limit after replacing the

bushing, replace the tension collar.

W1012489

Brake Lining Wear

1. Measure the brake lining thickness (T) with a depth gauge.
2. If the measurement is less than the allowable limit, replace the

PTO brake.

NOTE

■

• If the lining is carbonized or soaked with oil, replace the PTO

brake.

W1012662

Front PTO Pulley Wear

1. Measure the front PTO pulley O.D. with an outside micrometer.
2. If the measurement is less than the allowable limit, replace it.

W1012789

Clearance between
tension collar and
tension arm bushing

Factory spec.

0.002 to 0.114 mm
0.0001 to 0.0045 in.

Allowable limit

0.30 mm
0.0118 in.

Tension collar O.D.

Factory spec.

19.000 to 19.030 mm
0.7480 to 0.7492 in.

Tension arm bushing
I.D.

Factory spec.

19.032 to 19.114 mm
0.7493 to 0.7525 in.

Brake lining thickness
(T)

Factory spec.

5.7 to 6.3 mm
0.224 to 0.248 in.

Allowable limit

4.0 mm
0.157 in.

Front PTO pulley O.D.

Factory spec.

123.9 to 124.0 mm
4.878 to 4.882 in.

Allowable limit

123.0 mm
4.843 in.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 227 / 395

Результаты поиска

Содержание G2160

Отзывы: