manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 329 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 329

P1-S17

G2460G, WSM

ENGINE

[2] ENGINE  BODY

(1) Checking and Adjusting

Compression Pressure

1. After warming up the engine, stop it and remove the air cleaner,

the muffler and all spark plugs.

2. Install a compression tester (Code No: 07909-30251) for

gasoline engines to spark plug hole.

3. Run the engine at 7.5 S

-1

 (450 rpm) with the starter for 5 to 10

seconds keeping throttle valve fully open.

4. Read the maximum pressure.  Measure the pressure more than

twice.

5. If the measurement is below the allowable limit, apply a small

amount of oil to the cylinder wall through the spark plug holes and
measure the compression pressure again.

6. If the compression pressure is still less than the allowable limit,

check the top clearance, valve and cylinder head.

7. If the pressure increases after applying oil, check the cylinder

wall and piston rings.

NOTE

■

• Check the compression pressure with the specified valve

clearance.

• Always use a fully charged battery for performing this test.
• Variances in cylinder compression values should be under

10 %

.

W1022479

Top Clearance

1. Remove the cylinder head and the head gasket completely.
2. Bring the piston to it TDC, and fasten 1.5 mm dia. 5 to 7 mm long

fuse wires to 3 to 4 spots on the piston top with grease so as to
avoid the intake and exhaust valve and the combustion chamber
ports.

3. Bring the piston to its middle position, install the cylinder head,

and tighten the cylinder head bolts to specification.  
(Head gasket must be changed to new one.)

4. Turn the flywheel until the piston passes through the TDC.
5. Remove the cylinder head, and measure the thickness of the

fuses.

6. If the measurement is not within the factory specifications, check

the oil clearance between the crankpin and bearing and between
the piston pin and bushing.

NOTE

■

• After checking the top clearance, be sure to assemble the

cylinder head with a new cylinder head gasket.

W10107680

Compression pressure

Factory spec.

1.27 MPa
13.0 kgf/cm

2

185 psi

Allowable limit

0.88 MPa
9.0 kgf/cm

2

128 psi

Top clearance
(Engine serial No.: above 1A0001)

Factory spec.

0.85 to 1.30 mm
0.0335 to 0.0512 in.

Top clearance
(Engine serial No.: below YY8644)

1.45 to 1.75 mm
0.057 to 0.0690 in.

Tightening torque

Cylinder head bolt

37.2 to 42.1 N·m
3.8 to 4.3 kgf·m
28.0 to 31.7 ft-lbs

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов