Kubota G2160 Скачать руководство пользователя страница 156

Страница: 156 / 395

3-S7

G2160, WSM

BRAKE

[3] SERVICING

Brake Lining Wear

1. Measure the brake lining thickness with vernier caliper.
2. If the measurement is less than the allowable limit, replace the

brake shoes.

NOTE

■

• If the lining is carbonized or soaked with oil, replace the

shoes.

W1014697

Brake Drum Wear

1. Measure the brake drum I.D. with vernier caliper.
2. If the measurement exceeds the allowable limit, replace it.

W1014861

Brake lining thickness

Factory spec.

9.0 mm
0.35 in.

Allowable limit

7.5 mm
0.30 in.

Brake drum I.D.

Factory spec.

81.2 to 81.4 mm
3.197 to 3.205 in.

Allowable limit

82.0 mm
3.228 in.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 156 / 395

Результаты поиска

Содержание G2160

Отзывы: