Kubota G2160 Скачать руководство пользователя страница 340

Страница: 340 / 395

P1-S28

G2460G, WSM

ENGINE

Adjusting Engine Speed

1. Warm up the engine at a medium speed for 10 to 15 minutes.
2. Engine speed is adjusted to approx. 1500 rpm by the speed

control lever (3).

3. Throttle valve (1) is closed by hand and the rpm of the engine is

adjusted with the throttle adjust screw (2) to 1200 rpm (1100 to
1300 rpm).

4. Adjust the low-idling speed adjust screw (4) until the engine rpm

reaches 1500 rpm (1400 to 1600 rpm) with the speed control
lever (3) in the minimum speed position.

5. Adjust the high-idling speed adjust screw (5) until the engine

speed reaches 3250 rpm (3200 to 3250 rpm) with the speed
control lever (3) in the maximum speed position.

W1076471

(1) Throttle Valve
(2) Throttle Adjust Screw
(3) Speed Control Lever

(4) Low-Idling Adjust Screw
(5) High-Idling Adjust Screw
(6) Carburetor

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды