manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 236 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 236

8-M7

G2160, WSM

ELECTRICAL SYSTEM

■

KRA system Operating Mode
“Operating mode” is set up as follows:

1. Start the engine.
2. Set the throttle lever to the “FAST” position (A).
3. Push down the PTO lever to the “ENGAGED”

position.

W1013204

KRA system Operating Mode
- In KRA system operating mode, engine is stopped by depressing speed control pedal to “REVERSE”.
- This engine stopping is controlled by current flow to key stop timer in diesel engine or ignition unit in gasoline

engine.

- In PTO works such as mowing, while mowing and depressing speed control pedal to “NEUTRAL” or

“REVERSE”, PTO switch’s contact point is contacted.
At this moment, electrical current flows as the above figure.

- Since the electrical circuit between main switch and PTO switch is cut off, electrical current from main switch

does not flow to PTO switch.
Reverse switch keeps “ON”, and electrical circuit between main switch and engine is cut off as shown in the
above figure.  Current from main switch does not flow to key stop timer through reverse switch.

- On the other hand, electrical current from main switch flows to engine stop solenoid through key stop timer.

Current from battery directly flows to key stop timer and engine is stopped.

W1018740

(1) Throttle Lever

(A) “FAST” Position
(B) “SLOW” Position

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов