manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 341 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 341

P1-S29

G2460G, WSM

ENGINE

(2) Carburetor

(A) Altitude Compensation Kit (Engine Serial No.: Above 1A0001)

Main Jet and Pilot Jet

1. Remove the carburetor.
2. Loosen the drain screw (3) to let fuel out.
3. Remove the gasoline solenoid (6).
4. Remove the main jet (5).
5. Install the high-altitude kit's main jet onto the carburetor.
6. Tighten the throttle adjust screw (4) and remove the screw (1).
7. Replace the existing pilot jet (2) with the high-altitude kit's pilot jet.
8. Install the gasoline solenoid (6).
9. Install the carburetor in place.  (See page P1-S19.)
10.Readjust the governor.  (See page P1-S27.) 
11.Adjust the engine speed.  (See page P1-S28.) 

NOTE

■

• After install the carburetor, the adjustment of governor and

engine speed are executed.  (See page P1-S27, S28.)

• Prepare a screwdriver that fits the main jet / pilot jet screws

in order not to damage the main jet and pilot jet.

• Replace the air cleaner packing and the carburetor packing

with new ones.

• Make sure there is no leak at the air cleaner packing and the

carburetor packing.

IMPORTANT

■

• Keep the carburetor inner parts which is removed from

standard carburetor.

W1018491

Tightening torque

Carburetor mounting nut

23.5 to 27.5 N·m
2.4 to 2.8 kgf·m
17.4 to 20.2 ft-lbs

Gasoline solenoid

7.8 to 11.7 N·m
0.8 to 1.2 kgf·m
5.8 to 8.7 ft-lbs

Main jet

1.0 to 2.9 N·m
0.1 to 0.29 kgf·m
5.0 to 15.2 ft-lbs

Pilot jet

1.0 to 3.9 N·m
0.1 to 0.40 kgf·m
5.0 to 20.5 ft-lbs

(1) Pilot Screw
(2) Pilot Jet
(3) Drain Screw

(4) Throttle Adjust Screw
(5) Main Jet
(6) Gasoline Solenoid

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов