manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 104 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 104

1-S44

G2160, WSM

ENGINE

Oil Clearance between Crankshaft Journal and Crankshaft
Bearing 2 and Crankshaft  Bearing 3

1. Put a strip of plastigage (Code No. 07909-30241) on the center

of the journal.

2. Install the bearing case and tighten the bearing case screws 1 to

the specified torque, and remove the bearing case again.

3. Measure the amount of the flattening with the scale, and get the

oil clearance.

4. If the oil clearance exceeds the allowable limit, replace the

crankshaft bearing 2 or 3.

5. If the same size bearing is useless because of the crankshaft

journal wear, replace it with an undersize one referring to the
table and figure.

NOTE

■

• Be sure not to move the crankshaft while the bearing case

screws are tightened.

(Reference)

• Undersize crankshaft bearing 2 and 3

• Undersize dimensions of crankshaft journal

W10344030

Oil clearance between 
crankshaft journal and 
crankshaft bearing 2 and 
crankshaft bearing 3

Factory spec.

0.028 to 0.059 mm
0.0011 to 0.0023 in.

Allowable limit

0.20 mm
0.0079 in.

Crankshaft journal O.D.
(Intermediate)

Factory spec.

39.934 to 39.950 mm
1.5722 to 1.5728 in.

Crankshaft bearing 3 I.D.

Factory spec.

39.978 to 39.993 mm
1.5739 to 1.5745 in.

Crankshaft journal O.D.
(Flywheel side)

Factory spec.

43.978 to 43.993 mm
1.7314 to 1.7320 in.

Crankshaft bearing 2 I.D.

Factory spec.

43.984 to 44.026 mm
1.7317 to 1.7333 in.

Undersize

Bearing

Code Number

Marking

0.2 mm
0.008 in.

Crankshaft bearing 2     
02

15694-23931

020 US

Crankshaft bearing 3    
 02

15861-23861

020 US

0.4 mm
0.016 in.

Crankshaft bearing 2     
04

15694-23941

040 US

Crankshaft bearing 3     
04

15861-23871

040 US

                 Undersize
Dimension

0.2 mm
0.008 in.

0.4 mm
0.016 in.

A

1.8 to 2.2 mm radius
0.071 to 0.087 in.radius

1.8 to 2.2 mm radius
0.071 to 0.087 in.radius

B

3.0 mm dia.
0.12 in. dia.

3.0 mm dia.
0.12 in. dia.

C

39.734 to 39.750 mm
1.56433 to 1.56496 in.

39.534 to 39.550 mm
1.55646 to 1.55709 in.

D

43.734 to 43.750 mm
1.72181 to 1.72244 in.

43.534 to 43.550 mm
1.71394 to 1.71457 in.

                               (0.8-S)

The crankshaft journal must be fine-finished to higher than                .

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов