Kubota G2160 Скачать руководство пользователя страница 271

Страница: 271 / 395

8-S31

G2160, WSM

ELECTRICAL SYSTEM

(2) KRA system Unit (Harness connector side)

KRA system Unit Connector Battery Voltage

1. Turn the main switch to “ON” position. But do not start the

engine.

2. Measure voltage with a voltmeter.

3. If 3 terminal - 8 terminal voltage is not battery voltage check the

KRA system fuse blown and wire harness disconnected.

4. If 5 terminal - 8 terminal, 6 terminal - 8 terminal voltage are not

battery voltage, check wire harness disconnected.

5. Continuity is not 0

, harness or KRA system switch is defective.

6. If KRA system fuse is not blown and wire harness is connected,

the KRA system unit is defective, and replace the KRA system
unit as an unit.

W1030717

KRA system Unit Connector Terminal Continuity

1. Measure the resistance with an ohmmeter when the main switch

is “OFF” position.

2. Push on the KRA system switch on panel board, and measure

the resistance between 1 terminal and 2 terminal.

W1031477

Voltage
(3 terminal- 8 terminal)

Factory spec.

Battery Voltage

Voltage
(5 terminal- 8 terminal)
HST pedal “Neutral” or
“Forward”

Factory spec.

Battery Voltage

Voltage
(6 terminal- 8 terminal)
PTO lever “Disengage”

Factory spec.

Battery Voltage

(1) KRA System Switch
(2) KRA System Switch
(3) Fuse
(4) Start Switch

(5) Reverse Switch
(6) PTO Switch
(7) Lamp
(8) GND.

Resistance-
(1 Terminal - 2 Terminal)

Factory spec.

Resistance-
(8 Terminal - Chassis)

Factory spec.

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 271 / 395

Результаты поиска

Содержание G2160

Отзывы: