Kubota G2160 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 395

background image

1-S23

G2160, WSM

ENGINE

(B) Timing Gears and Camshaft

Injection Pump and Speed Control Plate

1. Remove the socket head screws and nuts, and remove the

injection pump (3).

2. Remove the screws and separate the speed control plate (2),

taking care not to damage the spring (4).

3. Disconnect the spring (4) and remove the speed control plate (2).
(When reassembling)

• Hook the spring (4) to the lever (5) first and install the speed

control plate (2).

• Be sure to place the copper washers underneath two screws (1)

(as shown in the figure).

• Position the slot (9) on the fork lever just under the slot (8) on the

crankcase.

• Insert the injection pump (3) so that the control rod (7) should be

pushed by the spring (6) at its end and the pin (10) on the rod
engages with the slot (9) on the fork lever (as shown in the
figure).

NOTE

■

• The sealant is applied to both sides of the soft metal gasket

shim. The liquid gasket is not required for assembling.

• Addition or reduction of shim (0.05 mm, 0.0020 in.) delays or

advances the injection timing by approx. 0.0087 rad (0.5

°

).

• In disassembling and replacing, be sure to use the same

number of new gasket shims with the same thickness.

W10167080

Fan Drive Pulley

1. Set the stopper to the flywheel.
2. Remove the fan drive pulley retaining screw.
3. Draw out the fan drive pulley with a puller.
(When reassembling)

• Install the pulley to the crankshaft, aligning the mark (1) on them.
• Apply engine oil to the fan drive pulley retaining screws.

And tighten them.

W10172470

(1) Screws and Copper Washers
(2) Speed Control Plate
(3) Injection Pump
(4) Spring
(5) Lever

(6) Spring
(7) Control Rod
(8) Slot (Crankcase Side)
(9) Slot (Fork Lever Side)

(10) Pin

Tightening torque

Fan drive pulley retaining
screw

117.6 to 127.4 N·m
12.0 to 13.0 kgf·m
86.8 to 94.0 ft-lbs

(1) Aligning Mark

KiSC issued 11, 2006 A

«
...
81
82
83
84
85
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G2160

Бренд: Gearmore Страницы: 14

Бренд: Mahindra Страницы: 140

Бренд: Nordic Auto Plow Страницы: 7

Jinma 200 Series

Бренд: Yancheng Tractor Factory Страницы: 52

Бренд: Troy-Bilt Страницы: 44

Бренд: Kalmar Страницы: 88

FORTERRA HD Series

Бренд: Zetor Страницы: 168

Бренд: Laney Страницы: 4

BOLENS 1050 192-02

Бренд: Husky Страницы: 16

Бренд: AL-KO Страницы: 20

Бренд: NPK Страницы: 29

Бренд: Bush Hog Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды