Kubota G2160 Скачать руководство пользователя страница 84

Страница: 84 / 395

1-S24

G2160, WSM

ENGINE

Gear Case

1. Remove the screw (1).
2. Disconnect the start spring (2) in the speed control plate

mounting hole.

3. Remove the gear case (3).
(When reassembling)

• Apply a liquid gasket (Three Bond 1215 or equivalent) to both

sides of the gear case gasket (4).

• Be sure to set three O-rings (5) inside the gear case.

W10174840

Idle Gear

1. Remove the external snap ring (3), the collar (2) and the idle gear

(1).

2. Remove the idle gear shaft mounting screws.
3. Remove the idle gear shaft.
(When reassembling)

• Install the idle gear, aligning the mark on the gears referring to

the figure.

• Apply engine oil to the idle gear shaft mounting screws.

And tighten them.

W1028418

(1) Screw
(2) Start Spring
(3) Gear Case

(4) Gear Case Gasket
(5) O-rings

Tightening torque

Idle gear shaft mounting
screw

9.8 to 11.3 N·m
1.00 to 1.15 kgf·m
7.2 to 8.3 ft-lbs

(1) Idle Gear
(2) Idle Gear Collar

(3) External Snap Ring

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Kubota G2160, Руководство по ремонту, Страница: 84 / 395

Результаты поиска

Содержание G2160

Отзывы: