Kubota G2160 Скачать руководство пользователя страница 258 | Manualshive

Страница: 258 / 395

Kubota G2160 Скачать руководство пользователя страница 258

8-S18

G2160, WSM

ELECTRICAL SYSTEM

Armature Coil

1. Check the continuity across the commutator and armature coil

core with an ohmmeter.

2. If it conducts, replace the armature.
3. Check the continuity across the segments of the commutator with

an ohmmeter.

4. If it does not conduct, replace the armature.

W1016056

Field Coil

1. Check the continuity across the lead (1) and brush (2) with an

ohmmeter.

2. If it does not conduct, replace the yoke assembly.
3. Check the continuity across the brush (2) and yoke (3) with an

ohmmeter.

4. If it conducts, replace the yoke assembly.

W1016179

Overrunning Clutch

1. Inspect the pinion for wear or damage.
2. If there is any defect, replace the overrunning clutch assembly.
3. Check that the pinion turns freely and smoothly in the

overrunning direction and does not slip in the cranking direction.

4. If the pinion slips or does not rotate in the both directions, replace

the overrunning clutch assembly.

W1016321

(1) Lead
(2) Brush

(3) Yoke

KiSC issued 11, 2006 A

«
...
256
257
258
259
260
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов