Kubota G2160 Скачать руководство пользователя страница 337 | Manualshive

Страница: 337 / 395

Kubota G2160 Скачать руководство пользователя страница 337

P1-S25

G2460G, WSM

ENGINE

Oil Pump and Crankshaft Gear

1. Remove the oil pump gear (6).
2. Remove the oil pump (5).
3. Remove the collar (4), O-ring (3) and oil slinger (2).
4. Remove the crankshaft gear (1) with a puller.
(When reassembling)

• Install the collar after aligning the marks on the gears. (See the

figure at “Idle Gear and Camshaft”.)

W10180290

(D) Crankshaft

Flywheel

1. Fit the stopper to the flywheel.
2. At first, remove two pieces of the flywheel screws.
3. Insert two pieces of the flywheel guide screws in the holes.
4. Remove all flywheel screws.
5. Remove the flywheel slowly along the flywheel guide screws.
(When reassembling)

• Insert two pieces of the flywheel guide screws.
• Fit the flywheel giving care to the position of the knock pin.
• Apply engine oil to the threads and the undercut surface of the

flywheel bolt and fit the bolt.

W10290240

(1) Crankshaft Gear
(2) Crankshaft Oil Slinger
(3) O-ring

(4) Crankshaft Collar
(5) Oil Pump
(6) Oil Pump Gear

Tightening torque

Flywheel screw

53.9 to 58.8 N·m
5.5 to 6.0 kgf·m
39.8 to 43.4 ft-lbs

KiSC issued 11, 2006 A

«
...
335
336
337
338
339
...
»

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов