Kubota G2160 Скачать руководство пользователя страница 365

Страница: 365 / 395

QG-7

G2160-R48S, WSM

G GENERAL

(3) Check Points of Every 50 Hours

Adjusting Brake Play

CAUTION

• When making adjustments, park the machine on a flat area,

block wheels, stop engine and remove the key.

1. If brake play is not correct, loose the lock nut (2) and turn the nut

(3) in the desired direction until the proper play is achieved.

2. After adjustment, retighten lock nut (2) securely.

W1013627

Greasing

CAUTION

• Be sure to stop the engine and remove the key before

greasing.

1. Apply grease to the following points.

W1013774

(4) Check Points of Every 200 Hours

Checking Hydraulic Hose

CAUTION

• Be sure to stop the engine and remove the key before

checking and replacing hydraulic hose.

• Allow transmission case to cool down sufficiently; oil can be

hot and may cause burns.
Check to see hydraulic hoses are properly fixed every 200 hours
of operation.

1. Check to see that all lines and hose clamps are tight and not

damaged.

2. If hoses and clamp are found worn or damaged, replace or repair

them at once.

W1013887

Brake play

Factory spec.

15 to 25 mm
0.59 to 0.98 in.

(1) Brake Pedal
(2) Lock Nut
(3) Nut
(4) Spring

(A) Brake Play

(1) Grease Nipple

(Side Blade Shaft (LH, RH))

(2) Grease Nipple

(Center Blade Shaft)

(3) Grease Nipple (Mower Tension Arm)

(1) Mower Lift Cylinder Hose

(2) Grass Hopper Dump Cylinder

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды