manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 144 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 144

2-S22

G2160, WSM

TRANSMISSION AND REAR AXLE

[3] SERVICING

(1) Hydostatic Transmission

Auxiliary Pump

1. Check the charge pump housing (2) and the gerotor assembly (1)

for scratches and wear.

2. If scratch or worn, replace the charge pump complete assembly.

W1047558

Pump Shaft and Motor Shaft

1. Check the seal surface (1), the bearing surface (2) and the ball

bearing (3).   

2. If the shaft is rough or groove, replace it.  
3. If the ball bearing is worn, replace it.   

W1033016

Cylinder Block Assembly

1. Check the cylinder blocks (1) and piston (5) for scratches and

wear.   

2. If scratch or worm, replace the cylinder block assembly.  
3. Check that the piston (5), spring (2) spring seat (3) and ball (4)

are in each cylinder bore.

4. Check the pistons for their free movement in the cylinder block

bores.   

5. If the piston or the cylinder block is scored, replace the cylinder

block assembly.   

6. Check the polished face of cylinder block for scording.  
7. If scored, replace the cylinder block assembly.   

IMPORTANT

■

• Do not interchange pistons between pump and motor

cylinder block. Pistons and cylinder blocks are matched. 

W1033158

(1) Gerotor Assembly

(2) Charge Pump Housing

(1) Seal Surface
(2) Bearing Surface

(3) Ball Bearing

(1) Cylinder Block
(2) Spring
(3) Spring Seat

(4) Ball
(5) Piston

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов