manualshive.com logo in svg

Kubota G2160, Руководство по ремонту, Страница: 286 / 395

Поделиться
Скачать
Kubota G2160 Скачать руководство пользователя страница 286

9-S13

G2160, WSM

MOWER

Outer Pulley and Blade Shaft

1. Unscrew the outer pulley mounting nut (21), and remove the

outer pulley (27).

2. Unscrew the pulley holder mounting nut (29) and remove the left

pulley holder (35),

3. Remove the oil seal (37) and tap out the left blade shaft (38) with

the ball bearings (36), (32) taking care not to damage the grease
nipple (20).

4. Remove the oil seal (31).
5. Remove the ball bearings (36), (32) and collar (33) from the blade

shaft(38).

6. Remove the right pulley holder (15) and blade shaft (19) as

above.

(When reassembling)

• Replace the oil seals (31), (37), (12) and (18) with new ones.

W1015887

Tightening 
torque

Outer pulley mounting nut

196.1 to 225.6 N·m
20.0 to 23.0 kgf·m
144.7 to 166.4 ft-lbs

Pulley boss mounting nut

23.5 to 27.4 N·m
2.4 to 2.8 kgf·m
17.4 to 20.3 ft-lbs

Pulley holder 
mounting nut

RCK54-24G
RCK60B-24G

77.4 to 90.2 N·m
7.9 to 9.2 kgf·m
57.1 to 66.5 ft-lbs

(1) Grease Nipple
(2) Outer Pulley Mounting Nut
(3) Spring Washer
(4) Plain Washer
(5) Outer Pulley Boss (Right)
(6) Outer Pulley (Right)
(7) Pulley Boss Mounting Nut
(8) Spring Washer
(9) Pulley Boss Mounting Bolt

(10) Pulley Holder Mounting Nut
(11) Spring Washer
(12) Oil Seal
(13) Ball Bearing
(14) Collar
(15) Pulley Holder (Right)
(16) Pulley Holder Mounting Bolt
(17) Ball Bearing
(18) Oil Seal
(19) Blade Shaft (Right)

(20) Grease Nipple
(21) Outer Pulley Mounting Nut
(22) Spring Washer
(23) Plain Washer
(24) Pulley Boss Mounting Nut
(25) Spring Washer
(26) Outer Pulley Boss (Left)
(27) Outer Pulley (Left)
(28) Pulley Boss Mounting Bolt
(29) Pulley Holder Mounting Nut
(30) Spring Washer
(31) Oil Seal
(32) Ball Bearing
(33) Collar
(34) Pulley Holder (Left)
(35) Pulley Holder Mounting Bolt
(36) Ball Bearing
(37) Oil Seal
(38) Blade Shaft (Left)

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Отзывы:

Нет отзывов