Kubota G2160 Скачать руководство пользователя страница 89

Страница: 89 / 395

1-S29

G2160, WSM

ENGINE

(D) Crankshaft

Flywheel

1. Lock the flywheel not to turn using flywheel stopper.
2. Remove the flywheel screws, except for two which must be

loosened and left as they are.

3. Set a flywheel puller (Code No: 07916-32011), and remove the

flywheel.

(When reassembling)

• Apply engine oil to the flywheel screws. And tighten them.

W1030810

Bearing Case Cover

1. Remove the bearing case cover mounting screws. First, remove

inside screws and then outside screws.

(When reassembling)

• Fit the bearing case gasket (3) and the bearing case cover gasket

(4) with correct directions.

• Apply liquid-type gasket (Three Bond 1215 or its equivalent) to

both sides of a new bearing case cover gasket.

• Install the bearing case cover to position the casting mark “

↑

” (1)

on it upward.

• Apply engine oil to the oil seal lip and take care that it is not rolled

when installing.

• Tighten the bearing case cover mounting screws with even force

on the diagonal line.

W1031168

Tightening torque

Flywheel bolt

53.9 to 58.8 N·m
5.5 to 6.0 kgf·m
39.8 to 43.4 ft-lbs

(1) Mark
(2) Mark Bearing Case Cover
(3) Bearing Case Gasket
(4) Bearing Case Cover Gasket

(A) Upside

KiSC issued 11, 2006 A

Содержание G2160












































































































































































































































































































































































































Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды

Kubota G2160, Руководство по ремонту

Результаты поиска

Содержание G2160

Отзывы:

Похожие инструкции для G2160

Бренды по названию

Популярные бренды